Schluter DITRA-HEAT-E-HK Câble de plancher chauffant électrique 240V 282.1' (85.3 pi²)

Regular price: $633.35

Description

Schluter-DITRA-HEAT-E-HK heating cables are twisted pairs designed to integrate with the DITRA-HEAT uncoupling membrane and heat interior floors. Important guidance for selection and installation: - Do not use cable to cover the entire tiled surface: this is generally unnecessary. - Very important: NEVER CUT OR MODIFY the cable. Any alteration changes its resistance, may damage it, and can cause overheating. - It is possible to lay the cable using alternating spacing of three then two studs in certain areas or across the whole floor to increase output (e.g., over an uninsulated subfloor or concrete) or to use a longer cable when three-stud spacing prevents meeting minimum clearances from walls and partitions. - Four-stud spacing is not recommended because it can cause uneven heating. - Observe the following minimum clearances: walls, partitions and fixed cabinets 2" (50 mm); heat sources (electric baseboards, fireplaces, forced-air heating systems, etc.) 8" (200 mm); floor drains and forced-air ducts 4" (100 mm); centerline of toilet drains 7" (180 mm). - NEVER install cable under vanity cabinets with no airflow, under bathtub platforms or freestanding tubs with no airflow, or inside cabinets, islands, small storage spaces or closets where the floor covering continues: these confined areas can cause overheating. - NEVER run the cable under or through a wall, partition, or through a floor. - NEVER place the splice (the black plastic piece joining the cold lead to the gray cable) inside a wall; it must be fully embedded beneath the floor covering, per installation instructions. - Provide a buffer zone — for example behind a toilet or near a door — to hide excess cable and avoid heating a nonessential area. Cables can also be installed 6" (150 mm) from walls to create this buffer. - Test the cable while it is still on its spool and at two additional stages of installation to verify integrity and protect the warranty. A megohmmeter is required for the insulation resistance test; its use is strongly recommended. - Consult a qualified electrician before ordering DITRA-HEAT cables to select the correct voltage for your installation.

Read less

Specifications

Manufacturer	Schluter
Radiant system compatibility	Yes
Coverage (m²)	7.9
Coverage (ft²)	85.30
Maximum coverage (m²)	7.9
Maximum coverage (ft²)	85.3
Minimum coverage (m²)	6.6
Minimum coverage (ft²)	71.1
Warranty	DITRA-HEAT System - Limited 15-year warranty
Warranty (years)	15
Height (mm)	17
Height (in.)	0.1633
Height (inch fraction)	5/32
Included	Sensor
Width (mm)	27
Length (mm)	52
Collection name	DITRA-HEAT-E-HK
Linear foot	282.1
Weight (lb)	8.62
Type of radiant system	Electric heating only
Indoor use	Yes
Voltage (V)	240

Number of unit(s)

Documents

DITRA-HEAT Technical Data Sheet (DHEHK24085)DITRA-HEAT and DITRA-HEAT-DUO Brochure (DHEHK24085)DITRA-HEAT System warranty document (DHEHK24085)User guide DITRA-HEAT Technical Bulletin for alternate coverings (DHEHK24085)User guide DITRA-HEAT Installation Manual (DHEHK24085)User guide DITRA-HEAT Spreadsheet (DHEHK24085)

Technical information

Quick and simplified installation: the cables insert into the membrane without fasteners, without covering with self-leveling compound and without return to the thermostat, speeding up installation.
Designed for under tile, stone and resilient coverings (e.g. LVT) — provides efficient electric underfloor heating.
Produce virtually zero electromagnetic fields.
Available in 120 V and 240 V cables and in several lengths to suit different projects.
Included: Sensor